Restoring your hail damaged vehicle recommendations

Several advices for paintless dent repair jobs: Hailstorm damage is a car owner’s worst nightmare and can easily be avoided with a few cautionary steps: try to park your car in a shaded or covered area, especially during seasons when hailstorms are prevalent. If you’re going to be going out of town for an extended amount of time, make sure that your car is parked in an enclosed area and, if possible, have someone check on it once in a while. Open spaces will leave your car helpless against the wrath of this natural phenomenon.

First let’s begin with some car paint care tricks: Repair times are up to the severity of the hailstorm and the damage on your car. For the light or moderate damages, the repairs may take from 1 to 3 days. But for heavy damages, it may take you 2 to 3 weeks as that damages will needs body shop participation, for paint work and panel replacement.

If you want to polish your car and are considering buying a buffer, you can see my simplified approach to car polishing for the true beginner to achieve professional results. As the saying goes, “an ounce of prevention is worth a pound of cure”, and your car is no different. If you are just consistent with the basic instructions I have provided here, your car will not only look fabulous year after year, but will retain much more of its original value when you are ready to sell. Want to save your time and maximize your car detailing efforts. Unless you are a die hard car enthusiast, I actually recommend you find a quality, 100% cloth or hand wash, and take your car there at least every 2 weeks and let the crew there perform the grunt work of car washing.

Use Hot Glue, Wooden Dowels, & Screws: When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun. Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.

Undercoating: Although waxing the car and polishing it produces good results, you need to protect the car from long term damage by undercoating and rust-proofing it. When the car metal is oxidized, rust sets in and destroys the surface of the car. To avoid this, you should consider rust-proofing the vehicle, particularly if you reside in a state where the humidity is high. Read extra information at Auto Repair Colorado Springs.

Dents near edges – If a dent of any size is situated near the very edge of a body panel or near a seam, PDR repair may be impossible. The reason for this is that in order to repair a dent using these techniques, you need to access the back side of the dent. The dent has a crease – If there is a sharp crease (like a folded page) in the dent, PDR likely will not work. Older vehicles – If your vehicle is older than 1990 or is a classic car, the odds are good that attempting paintless repair techniques on a dent will damage the paint. This is because the paint quality on older body panels can’t withstand the strain of the repair techniques.

First, you have to pick a proper tool kit. And that’s not easy for a user who has little clue what’s going on. Some of them are cheap — low prices should raise red flags. Others are so expensive (three-figures or more) that they’re probably right up there with the cost of a decent professional repair (although, to be fair, if you buy the kit you can perform multiple repairs). Many of the high-end, expensive tools are intended to be used along the inside of the panel, much like a pro would do. (Gaining access to the inside of body panels can be a chore, though, and often involves careful removal of multiple interior trim pieces.) Alternatives (which tend to be the less expensive kits) flaunt the conventional wisdom that small dents should be massaged back out from behind the painted surface. These options instruct the user to glue a tool to the dented surface and then twist or pull on the tool to pop it out. True, you can go buy the same tools as a pro, but it takes a lot of skill and experience to use them properly.