Customize my ride

Paintless dent repair in Macungie, PA? The first step to performing a dent repair without using paint involves assessing the dent itself and determining if a paintless dent repair is even possible. According to most experts, 80 to 90 percent of dents can be repaired using PDR techniques. However, there are a certain percentage of dents that are impossible to repair without following it up with a paint job. The following types of dents usually fall into this “non-PDR” category: Very deep dents – Even very large dents can be repaired using PDR if the dent is fairly shallow. However, if a dent of any size is pushed in too far, the metal can’t be bent back into place without damaging the paint and requiring repainting.

In the first place let’s start with some car paint care tricks: Using the Right Wax. Since each type of paint reacts differently to wax and polish, you need to find out which paint was used on your car and purchase detailing products that suit the paint. Some products may act as abrasive agents and strip the car off its original shine.

So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.

This technique is popular among automotive enthusiasts when it comes to the removal of small dents. The idea is simple: heat will inevitably cause the metal surface to expand and (hopefully) pop the dent out. Remember that the more time the car spends time under the sun, the better this technique will work. Use a plastic and/or leather conditioner for the car’s interior, so as to not damage it while exposing the car to maximum sunlight. If the sun’s heat isn’t particularly strong that day, a simple hair dryer could be used in conjunction with the sun to concentrate the heat to a specific area. Point the hair dryer to the dented area for two-minute intervals until the dent pops out. Be careful not to touch the hot lip of the hair dryer on any painted surface. A two-to-four inch gap between the dryer and the surface is recommended.

Applying dry ice to the dent is an effective way for fixing hail damage. The huge change in temperature can force the dents to pop out. Everything for you to do is just moving the dry ice around the damaged area to cool the area rapidly. But be careful as dry ice will damage your skin if you don’t wear gloves when handling it. Fixing hail damage by dry ice can be a cool solution, but sometimes it can not remove all of the dents. So in this case, you will need to do additional repairs.

I don’t care if you wash your car yourself (more on that strategy later in this page) or you take it to a quality car wash. (Yes, not all car washes are created equal) This is not an option as dirt is your #1 enemy when it comes to the finish on your new car paint. And this doesn’t mean once every 6 months whether it needs it or not. This means regularly and consistently. (A minimum of once a month…minimum!)

We recommend going to a professional repair service to avoid a lot of extra costs. Meet EvidentPDR in Colorado. We deliver the best workmanship and craftsmanship while relentlessly focusing on customer service, all while exceeding customer expectations. Our team is well known, highly-skilled technicians, and business-savvy professionals. Our culture and results-driven ethos is what defines our Print and Automotive shop. We make sure every customer is proud to do business with Evident PDR! Find additional details at Auto dent repair Colorado Springs.

Only three things in life are certain: death, taxes, and getting a dent in your car or truck. Even if you’re as careful as possible, you can’t always account for runaway shopping carts, wrongly thrown footballs, out-of-nowhere light posts, and other real-life annoyances. However you got your dent or ding, the next thing on your mind is, undoubtedly, how to get it out. Sure, you can take it to a body shop or friendly neighborhood mechanic for repair, but their price quotes can be unbelievable, especially if they want to remove the paint first or use body filler. $200 for that tiny dent?! I don’t think so.